Re: Does Informix Online 7.30.UC2-1 run on Unixware 7.1
Tam McLaughlin said Informix Online 7.30.UC2-1 was not supported on UnixWare 7.1 (they used 7.01) because the rewritten networking caused panics in stress tests. Another poster said Informix had since certified 7.1. A third ran 7.30UC2-1 on 7.1 without networking. Peter J Diaz de Leon ordered 7.30.UC10-1 for 7.1 and asked about 7.31 or 9.20 ports; unanswered.
Auto-generated by Claude from the posts below — may be imperfect; read the full thread.
Leandro Dardini wrote: > I read on the specs that it runs on Unixware 7.0, but does it run also on > version 7.1? > I try to install it, but I get an error in shared memory creation: the > system ask me to check SHMSEG, but it is on its maximum... (and over) > As far as I am aware, it is not supported on Unixware 7.1 which meant we had to go with unixware 7.01. The networking components of unixware 7.1 have apparently been rewritten differently from unizware 7.01 and have caused some problems with some stress tests where unixware 7.1 panics. We have been told by Informix that the next release/update from Unixware 7.1 should fix the problem.
In article <385CE003.8DEB73D2@net.ntl.com>, tam.mclaughlin@net.ntl.com wrote: > > > Leandro Dardini wrote: > > > I read on the specs that it runs on Unixware 7.0, but does it run also on > > version 7.1? > > I try to install it, but I get an error in shared memory creation: the > > system ask me to check SHMSEG, but it is on its maximum... (and over) > > > > As far as I am aware, it is not supported on Unixware 7.1 which meant we had > to go with > unixware 7.01. The networking components of unixware 7.1 have apparently been > rewritten differently from unizware 7.01 and have caused some problems with > some stress tests where unixware 7.1 panics. We have been told by Informix > that the next release/update from Unixware 7.1 should fix the problem. It has just been certified by Informix a couple of days ago for 7.1. I am not sure if it is with UC2-1 or a newer patch release. Check their website, click on Partners->Roadmap->SCO Thanh > > Sent via Deja.com http://www.deja.com/ Before you buy.
I have my production IDS engine running on UW7.0.1 and my development IDS 7.30UC2-1 running on my laptop with UW7.1 (64MB memory). I have not patched the UW7.1 system, but I also do not have any networking set up (yet). Anyone know when Informix will be releasing 7.30UCx (higher than 2-1)? > tam.mclaughlin@net.ntl.com wrote: <snip> > > > I try to install it, but I get an error in shared memory creation: > the > > > system ask me to check SHMSEG, but it is on its maximum... (and I have the following settings on my UW7.1 system: SEMMNI 150 SEMMSL 150 SHMMAX 8192000 SHMMNI 175 SHMSEG 10 > over) > > > > > > > As far as I am aware, it is not supported on Unixware 7.1 which meant > we had > > to go with > > unixware 7.01. The networking components of unixware 7.1 have > apparently been > > rewritten differently from unizware 7.01 and have caused some > problems with > > some stress tests where unixware 7.1 panics. We have been told by > Informix > > that the next release/update from Unixware 7.1 should fix the problem. > > It has just been certified by Informix a couple of days ago for 7.1. > I am not sure if it is with UC2-1 or a newer patch release. > Check their website, click on Partners->Roadmap->SCO > > Thanh > > Sent via Deja.com http://www.deja.com/ Before you buy.
On Mon, 20 Dec 1999 01:24:20 GMT, tqma@my-deja.com wrote: >It has just been certified by Informix a couple of days ago for 7.1. >I am not sure if it is with UC2-1 or a newer patch release. >Check their website, click on Partners->Roadmap->SCO > >Thanh >> >> > > >Sent via Deja.com http://www.deja.com/ >Before you buy. I just ordered ISD 7.30.UC10-1 for Unixware 7.1 I wish they would get 7.31 ported or for that matter 9.20. Does anyone know if this is in the works? Thanks Peter